This is a battery cell case that was a pain last time I printed it with supports
Caveat: I know nothing about 3D printing.
That being said, couldn't you just print it on its side?
this post was submitted on 17 Dec 2024
163 points (100.0% liked)
3DPrinting
15763 readers
35 users here now
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
Rules
-
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
-
Be respectful, especially when disagreeing. Everyone should feel welcome here.
-
No porn (NSFW prints are acceptable but must be marked NSFW)
-
No Ads / Spamming / Guerrilla Marketing
-
Do not create links to reddit
-
If you see an issue please flag it
-
No guns
-
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
founded 2 years ago
MODERATORS
It really depends on what you're printing, how strong you need it to be, and/or what axis you don't mind looking uglier because of layer lines.
In this case OP might have been able to print it on a side with minimal supports, but the idea is that printing it at an angle turns things that would have been overhangs (which are hard for printers to do because of the melted plastic sagging) into upwards slopes. The alternative is adding support material that is intended to snap off (i.e. The block at the bottom of this picture), but those would be hard/impossible to remove in models like OP's that would have supports inside the holes.
That’s a great idea and would require similar amounts of support, however there’s still going to be 90 degree overhangs that wouldn’t come out quite as nice as the orientation I used
The model in question only has 1 flat side, its end (which is the top in the photo). Every other side requires supports if it’s on the build plate because of the recess in the cap, and the cap being wider than the rest of the model
Ohh nice, battery pez dispenser!
Is that considered a raft + supports or just supports on there?
Just supports, I had to manually paint them in to prevent the slicer from putting them all the way up the side
In Orca slicer, if you use tree supports and hybrid, an option appears (advanced must be enabled) for something like "Essential supports only". It is so much better than spending all that time adding or blocking supports.
Ooh thanks I’ll give that a try
Would that be equivalent to PrusaSlicer's "automatic painting"?
I have no clue about that. I only recently stumbled across the orca setting while waging my own battle against excessively aggressive supports.
Looks like the model is just resting on supports. Might have a roof or "support interface" (a layer between supports and model)
As a total beginner, it's not really clear to me what's meant here. I read printing some things are better to print at an angle, like boxes, for additional strength. Is that what's meant here?
I think OP is putting it at an angle so there are no 90 degree overhangs and so the model doesn't need support added or removed.
What exactly is the difference to just printing it standing?
This model is almost entirely overhangs with small gaps between them, making support removal a pain. This way uses less filament and makes for better quality
Less overhangs?
That's one, but if you are priting a particularly delicate part, printing at an angle could strengthen the part significantly
How? What mechanisms, conditions, etc, are we manipulating which produce such a significant effect? After a bit of searching I found this write up:
https://thor3d.ca/wp/the-effects-of-print-orientation-on-strength/
Is this what we're referring to? To summarize (if I've understood this properly): Printing at 45 degrees ensures none of the print's three axes are aligned with the printer's least accurate axis of movement.
Similar, but I believe the strength addition is also because it changes the directions of the Z-axis layers.
Most filament is rather strong in tension. If you imagine printing a regular cube, without rotation, it’s going to be strongest stretching or compressing the sides of the cube.
But if you pulled the cube apart from its top and bottom, the only adhesive strength is the fused connection between layer heights. Which is super weak.
By printing at an angle, the layer heights may be in a direction that doesn’t receive tensile load, making it functionally stronger.
This particular model would have lots of troublesome bridging if printed vertically, and would need supports along the entire length if printed horizontally.
That's actually genius, thanks for the tip man
That's so smart! Thanks for the tip