3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
Honestly , I just clip the 2-3” off the front and not worry about it. It’s a minuscule amount of plastic
If you’re trying to be ultra frugal, yes, you can probably clean it off with a solvent. IPA might work. Goo gone would but introduces all sorts of other contaminants.
I admit I tried using every gram. Still I found some of the tape residue on the inside of the spool. Thanks for the advice.
I mean, honestly, it’s commendable.
I’d try IPA for the stuff in the middle. Or something like those blue 3m scrubbies.
Gotcha, thanks.
Apparently goo gone has limonene in it, I'd be wary of putting it anywhere near filament depending on the plastic used. I'm personally on the side of clip it and be done, I try to use as much as possible as well, have had the tail out on some spools get caught in the reverse bowden I use depending on the way its been wound, so I do tend to be on the cautious side and why I have smart filament sensors. Would rather lose 5g of filament over failing a print and wasting even more.
Yeah, technically it could, but tape sticks really well to most filament. It is more likely that whatever came out of the nozzle was in a dead zone. The nozzle back bore is drilled with a steeper angle than a typical bit, but it is not so acute that there are no dead zones. Sometimes filament can sit in those zones, cook, and go wonky. It happens more often with high temp filaments like polycarbonate. I run a bit of purging filament with every change and rarely have problems.
I would be more concerned about extruder gear issues with residue over time.
Glad to know. I wasn't aware of dead zones unil now. I'll have to research that.
Would it really cause problems if it did? I'm thinking if it got into the hotend (especially at the small amounts we're talking about), it would probably just melt into the molten filament and not really cause any issues.
There are "filament filters" that are for keeping foreign materials from getting into the hotend, but they're more for particulate things that won't melt and might clog the nozzle. Tape residue (again, at such small quanties) surely would just flow through with the molten filament and be unnoticeable in the final prints.
I guess it would be small. What about a small triangle of it?
I'm asking because I got a weird droplet in my feed that showed up in a duplicate print.
A small triangle of tape, or just tape adhesive?
I'd definitely be more inclined to think tape could be more of a concern than jist the adhesive. Probably if it were me, I'd just try to be more thorough about removing all the tape from the spool (and not worry about small amounts of residual adhesive.)
Also, a description and/or picture of the filament and tape you're talking about could help.
Yeah just the residue, no visible pieces of tape. Sorry for the late response.
Heads up btw, I've found that a good way to remove sticker residue on comic book bags/boards is to take the peeled sticker and use it to "blot" up the residue. It's possible that may work for you with the filament. Idk about your actual question though, seems like it'd be possible.
I'm not really concerned about my former issue. I hadn't yet touched the calibration settings of my printer. They made a significant difference. I got a completely different issue now which I'm certain is the big one that nobody has a set answer for.
Well I'm glad you fixed it by 25 days later lol.