I'm sure I'm massively overthinking this, but any help would be greatly appreciated.
I have a domain name that I bought through NameCheap and I've pointed it to Cloudflare (i.e. updated the name servers). I have a Synology NAS on which I run Docker and a few containers. Up until now I've done this using IP addresses and ports to access everything (I have a Homepage container running and just link to everything from there).
But I want to setup SSL and start running Vaultwarden, hence purchasing a domain name to make it all easier.
I tried creating an A record in Cloudflare to point to the internal IP of my NAS (and obviously, this couldn't be orange-clouded through CF because it's internal to my LAN). I'm very reluctant to point the A record to the external IP of my NAS (which, for added headache is dynamic, so I'd need to get some kind of DDNS) because I don't want to expose everything on my NAS to the Internet. In actual fact, I'm not precious about accessing any of this stuff over the internet - if I need remote access I have a Tailscale container running that I can connect to (more on that later in the post). The domain name was purely for ease of setting up SSL and Vaultwarden.
So I guess my questions are:
- What is the best way to go about this - do I create a DDNS on the NAS and point that external IP address to my domain in Cloudflare, then use Traefik to just expose the containers I want to have access to using subdomains?
- If so, then how do I know that all other ports aren't accessible (I assume because I'm only going to expose ports 80 and 443 in Traefik?)
- What do other people see (i.e. outside my network) if they go to my domain? How do I ensure they can't access my NAS and see some kind of page?
- Is there a benefit to using Cloudflare?
- How would Pi-hole and local DNS fit into this? I guess I could point my router at Pi-hole for DNS and create my A records on Pi-hole for all my subdomains - but what do I need to setup initially in Cloudflare?
- I also have a RPi that has a (very basic) website on it - how do I setup an A record to have Cloudflare point a sub-domain to the Pi's IP address?
- Going back to the Tailscale thing - is it possible to point the domain to the IP address of the Tailscale container, so that the domain is only accessible when I switch on the Tailscale VPN? Is this a good idea/bad idea? Is there a better way to do it?
I'm sure these are all noob-type questions, but for the past 6-7 years I've purely used this internally using IP:port combinations, so never had to worry about domain names and external exposure, etc.
Many thanks in advance!
I do this for some dockers in my unraid, except I use the zero trust tunnels. MUCH easier, can use SSL, and can set up a login page for users. Also, you don't have to open any ports on your router!
Im not sure about synology, but I would assume you can find a "cloudflared" docker in the app store.
check out this youtube video for a good explanation: https://www.youtube.com/watch?v=ZvIdFs3M5ic
A hundred times this. It's going to be the easiest to set up by a wide margin. https://www.cloudflare.com/products/tunnel/
Interesting, I've never considered Cloudflare Tunnels. Thanks.
However I do remember seeing this video the other day, that suggests perhaps it's not always the best solution? Not sure this applies here, though: https://www.youtube.com/watch?v=oqy3krzmSMA.
Christian brings up some great points worthy of consideration; however, if your going to use traditional routing through their network (A/cname) your still doing the same thing. CF will still see your traffic.
The second thing I should say is, I only use zero trust for websites I share with family. So, I have a Searxng and wef/voyager dockers running through zero trust.
For admin, homeassistant/iot/ip cams, I use an always on IPSec vpn on my iPhone, iPad, and steam deck (take it to work and plug into 3rd monitor) … this is cool because I get 24/7 ad blocking no matter where I am because it routes all my traffic through my pihole at home. This is a great solution for a single person, but I do not want to manage vpn access for multiple ppl. So, I agree with christian in NOT putting admin stuff/sensitive info behind CF at all (zero trust OR tradition web routing) unless you fully trust them. Otherwise do a 24/7 vpn like I do.
I don’t plan on exposing any of this stuff to anybody other than me. I do plan on spinning up SearX but it’ll only be me using it. I’ve given up trying to convince my family to move away from Google to even DuckDuckGo or Startpage, so there’s no way I’ll convince them to use SearX!
I think, therefore, for accessing away from home I’ll perhaps setup a subdomain that points to the IP of my Tailscale container — that means it’ll be accessible externally but only when I turn on the VPN.
When I’m on my home network I have a VPN on my Mac anyway.
Here is an alternative Piped link(s): https://piped.video/watch?v=ZvIdFs3M5ic
Piped is a privacy-respecting open-source alternative frontend to YouTube.
I'm open-source, check me out at GitHub.