snekerpimp

Setting up my server as a newbie some years ago, I did not have the ability to purchase more then one 8TB hard drive. Outgrew that rather quick and now I have two additional 16TB drives, in a Just A Bunch Of Disk configuration, mounted to different /mnt mount points. I know this is not ideal, but lacking the ability to expand further or buy new drives for a new zfs pool and transfer, I don't have much of a choice but to wipe the drives, set up a zfs raid and re-download everything.

I have everything set up in docker-compose files, so I'm pretty sure I just need to keep those and the folders where the configs are, modify the compose files with the new file structure and... I am unsure where to go from here. Will everything start being grabbed as soon as my dockers spin up? Is there an additional procedure I need to do to make sure I don't wipe my existing config files with blank empty ones? Is there an easier way of doing this?

I have an 8gb Raspberry Pi 4 that has been a workhorse for years. I keep it for my not intense but essential networking purposes, NetBoot.xyz, Homepage, etc., because I can run it over PoE (edit: Power over Ethernet), so it is always on as long as my network is up.

It is growing long in the tooth, and I find myself wanting to replace it with something a bit more capable. Looking at the 8gb Pi 5 at $80 plus another $30 for a PoE hat, I wonder if there is something out there that would be a better value for running PoE? Can you convert a micro pc over to PoE? Does anyone have any recommendations for computers that run off PoE or can be converted to PoE?

I am trying to set up a repository of knowledge for my job. Was thinking a wiki, but I need something that I can make as simple as possible for the end user, as some of them are not familiar with markdown or html. Is there a self hosted option that is dumb easy simple to navigate and edit for the end user?

I have friends and relatives that would like to do some memory and compute intensive tasks, but lack the hardware locally. I have loads of ram doing nothing and a little compute to spare. Is there a way for me to set up some service accessible to them that would allow them to spin up VMs, similar to Linode or DigitalOcean? I know letting outside access to a proxmox server would be disastrous. I guess I could setup a VPN server into a virtualized proxmox server? Would rather find a way to point them to a url with a username and password and have them able to use my server as their vps like AWS or Linode.

first off, thanks for everyone and their suggestions, and apologies for not responding back, was having issues with my personal lemmy instance.

I took everyone's advice and have gone test print crazy. I will attach the pictures to this post. I have tried to understand what I am looking at on my test prints in relation to what is not configured correctly on my printer. it's just not clicking. most of my prints look fine, the surface has good infill and the part looks ok from the outside, like benchie. but underneath, it looks like I am having either adhesion issues, bridging problems and support problems as well. but adjusting setting as suggested in here and here did not really improve anything, and in some cases made the print worse.

I am using the Flashprint slicer that came with the printer. I have tried cura and prusaslice and can't even get a print started on those, even with a raft. I'm sure they are better slicers that what Flashforge makes, but again, something just isn't clicking. any further advice would be greatly appreciated.

I am trying to finally get my homelab organized, and I need assistance visualizing my network. I am just wondering if there are tools out there that assist with this. I have tried the paint and gimp routes, and I find myself spending more time trying to make it look good and organized rather than actually mapping my network. Is there any utility out there that is purpose build just for visualizing network topology? Or am I better off with just graph paper, pencil and a straight edge?

Just picked up an APC 48u server rack. There were no pictures of it in the post and I did not notice until I got it home and set up, that the rack rails have threaded holes instead of square cage nut holes. I can’t seem to determine the thread size and pitch, and have a thread gauge coming. Until then, does anyone know anything about this? The people I grabbed it from had used self tapping machine screws and drove them in with an impact wrench. Is this what APC had intended, or is there some $300 proprietary screw I have to buy from them?